عرض مشاركة واحدة
قديم 10-14-2010, 02:15 AM رقم المشاركة : 7
معلومات العضو
م .نبيل زبن
المؤسس
 
الصورة الرمزية م .نبيل زبن
إحصائية العضو







 

م .نبيل زبن غير متواجد حالياً

 


افتراضي




Electrical interview question:How do you select a cable size (Cu & Al) for a particular
load?
Answer:At first calculate the electrical current of the load* after that derate the electrical current considering derating factor(depending on site condition and laying of cable) after choose the cable size from cable catalog considering derating electrical current.After that measure the length of cable required from supply point of load to load poin. Calculate the voltage drop which will max 3% (resistance and reactance of cable found from cable catalog of selecting cable) if voltage drop>3%
then choose next higher size of cable.


Electrical interview question:What are HRC fuses and where it is used?

Answer:HRC stand for "high rupturing capacity" fuse and it is used in distribution system for electrical transformers.



Electrical interview question:Which power plant has high load factor?

Answer:All base load power plants have a high load factor. If we use high efficiency power plants to supply the base load*we can reduce the cost of generation.Hydel power plants have a higher efficiency than thermal & nuclear power plants.



Electrical interview question:Mention the methods for starting an induction motor?

Answer:The different methods of starting an induction motor
DOL:direct online starter

Star delta starter
Auto transformer starter
Resistance starter
Series reactor starter



Electrical interview question:What is the difference between earth

resistance and earth electrode resistance?

Answer:Only one of the terminals is evident in the earth resistance. In order to find the second terminal we should recourse to its definition: Earth Resistance is the resistance existing between the electrically accessible part of a buried electrode and another point of the earth* which is far away.
The resistance of the electrode has the following components:
(A) the resistance of the metal and that of the connection to it.
(B) the contact resistance of the surrounding earth to the electrode.



Electrical interview question:What is use of lockout relay in ht voltage?

Answer:A lock-out relay is generally placed in line before or after the e-stop switch so the power can be shut off at one central location. This relay is powered by the same electrical source as the control power and is operated by a key lock switch. The relay itself may have up to 24 contact points within the unit itself. This allows the control power for multiple machines to be locked out by the turn of a single key switch.


Electrical interview question:What is the power factor of an alternator at no load?

Answer:At no load Synchronous Impedance of the alternator is responsible for creating angle difference. So it should be zero lagging like



Electrical interview question:Why most of analog o/p devices having o/p range 4 to 20 mA and not 0 to 20 mA ?
Answer:4-20 mA is a standard range used to indicate measured values for any process. The reason that 4ma is chosen instead of 0 mA is for fail safe operation .For example- a pressure instrument gives output 4mA to indicate 0 psi* up to 20 mA to indicate 100 psi* or full scale. Due to any problem in instrument (i.e) broken wire* its output reduces to 0 mA. So if range is 0-20 mA then we can differentiate whether it is due to broken wire or due to 0 psi.



Electrical interview question:Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Answer:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Electrical interview question:What is meant by knee point voltage?
Answer:Knee point voltage is calculated for electrical Current transformers and is very important factor to choose a CT. It is the voltage at which a CT gets saturated.(CT-current transformer).

Electrical interview question:What is reverse power relay?
Answer:Reverse Power flow relay are used in generating stations's protection. A generating stations is supposed to fed power to the grid and in case generating units are off*there is no generation in the plant then plant may take power from grid. To stop the flow of power from grid to generator we use reverse power relay.


Electrical interview question:What will happen if DC supply is given on the primary of a transformer?

Answer:Mainly transformer has high inductance and low resistance.In case of DC supply there is no inductance *only resistance will act in the electrical circuit. So high electrical current will flow through primary side of the transformer.So for this reason coil and insulation will burn out.



Electrical interview question:What is the difference between isolators and electrical circuit breakers? What is bus-bar?

Answer:Isolators are mainly for switching purpose under normal conditions but they cannot operate in fault conditions .Actually they used for isolating the CBs for maintenance. Whereas CB gets activated under fault conditions according to the fault detected.Bus bar is nothing but a junction where the power is getting distributed for independent loads.


Electrical interview question:What are the advantage of free wheeling diode in a Full Wave rectifier?


Answer:It reduces the harmonics and it also reduces sparking and arching across the mechanical switch so that it reduces the voltage spike seen in a inductive load


Electrical interview question:What are Motor Generator Sets and explain the different ways the motor generator set can be used ?
Answer:Motor Generator Sets are a combination of an electrical generator and an engine mounted together to form a single piece of equipment. Motor generator set is also referred to as a genset* or more commonly* a generatorThe motor generator set can used in the following different ways:
1.Alternating current (AC) to direct current (DC)
2.DC to AC
3.DC at one voltage to DC at another voltage
4.AC at one frequency to AC at another harmonically-related frequency








رد مع اقتباس